PassMyTest

CDL Pre-Trip Inspection Checklist

A printable checklist that follows the seven-step inspection method in the model CDL manual. Use it to practice for the vehicle inspection part of the CDL skills test and for your daily inspections.

Tip: choose "Save as PDF" as the printer to download it.

How the inspection test works

The vehicle inspection is the first part of the CDL skills test. The examiner may ask you to inspect all or part of the vehicle. Point to or touch each part, name it, and say what you are checking for, such as "mounted securely, not cracked, bent or broken, no leaks."

Step 1: Vehicle overview

Approach the vehicle and look at it as a whole.

  • General condition: damage, or the vehicle leaning to one side
  • Under the vehicle: fresh oil, coolant, grease or fuel leaks
  • Around the vehicle: people, other vehicles, objects, low wires or tree limbs
  • Last vehicle inspection report: make sure reported defects were repaired or found unnecessary to repair, and sign if required

Step 2: Engine compartment

Set the parking brake and/or chock the wheels, then raise the hood or tilt the cab (secure loose items first).

  • Engine oil level
  • Coolant level and condition of the radiator hoses
  • Power steering fluid level and hose condition (if equipped)
  • Windshield washer fluid level
  • Battery fluid level, connections and tie-downs (the battery may be mounted elsewhere)
  • Automatic transmission fluid level (may require the engine running)
  • Belts for tightness and excessive wear: alternator, water pump, air compressor
  • Leaks in the engine compartment: fuel, coolant, oil, power steering fluid, hydraulic fluid, battery fluid
  • Cracked or worn electrical wiring insulation

Step 3: Start the engine and inspect inside the cab

Parking brake on, transmission in neutral (or park), then start the engine and listen for unusual noises.

  • Oil pressure comes up to normal within seconds
  • Air pressure builds normally (on older single air systems, 50 to 90 psi within 3 minutes)
  • Ammeter or voltmeter in the normal range
  • Coolant and oil temperature rise gradually to normal
  • Warning lights and buzzers go out right away
  • Steering wheel play: no more than about 10 degrees (about 2 inches at the rim of a 20-inch wheel)
  • Clutch, accelerator, foot brake, trailer brake, parking brake and retarder
  • Transmission controls and interaxle differential lock (if equipped)
  • Horn(s), windshield wipers and washers
  • Headlights, dimmer switch, turn signals, four-way flashers, and parking, clearance, identification and marker lights
  • Mirrors and windshield: no cracks, dirt, illegal stickers or other obstructions; mirrors adjusted
  • Emergency equipment: spare electrical fuses (unless the vehicle has circuit breakers), three red reflective warning triangles, and a properly charged and rated fire extinguisher
  • Optional items: tire chains in winter, tire changing equipment, emergency phone numbers, accident reporting kit
  • Seat belt: securely mounted, adjusts and latches properly, not ripped or frayed

Step 4: Turn off the engine and check the lights

Set the parking brake, turn off the engine and take the key with you.

  • Turn on the low beam headlights and four-way flashers, then get out
  • At the front: low beams and both flashers work
  • Switch to high beams and check that they work
  • Turn off the headlights and flashers; turn on the parking, clearance, side-marker and identification lights
  • Turn on the right turn signal and start the walkaround

Step 5: Walkaround inspection

Walk around the vehicle, cleaning all lights, reflectors and glass as you go.

Left front

  • Driver door glass clean; door latches and locks work
  • Wheel and rim: no missing, bent or broken studs, clamps or lugs; no signs of misalignment
  • Tire: properly inflated, valve stem and cap OK, no serious cuts, bulges or tread wear (steer tires need at least 4/32 inch of tread)
  • Lug nuts: no rust trails or shiny threads that could mean looseness
  • Hub oil level OK, no leaks
  • Suspension: springs, spring hangers, shackles, U-bolts and shock absorbers
  • Brakes: drum or rotor, hoses, brake chamber and slack adjuster

Front

  • Front axle condition
  • Steering system: no loose, worn, bent, damaged or missing parts
  • Windshield: no damage, clean; wiper arms have proper spring tension and blades are secure
  • Lights and reflectors: clean, working and the proper color (amber at the front)
  • Right front turn signal: clean, working, proper color

Right side

  • Right front wheel, tire, suspension and brakes: same checks as the left front
  • Cab locks engaged (cab-over designs)
  • Fuel tank(s): securely mounted, not damaged or leaking, caps on and secure, enough fuel
  • Visible parts: no leaks at the rear of the engine or transmission; exhaust secure and not touching wires, fuel or air lines
  • Frame and cross members not bent or cracked; air lines and wiring secured against snagging and rubbing
  • Spare tire carrier and spare tire secure, right size and properly inflated
  • Cargo: properly blocked, braced, tied or chained; header board, side boards, stakes and tarps secure; doors closed and latched; oversize signs and permits in place if needed

Right rear

  • Wheels, rims and tires: same size, properly inflated, no cuts or bulges; dual tires not touching each other or other parts (other tires need at least 2/32 inch of tread)
  • Wheel bearings and seals not leaking
  • Suspension: springs, hangers, shackles, U-bolts, torque rods and shocks; axle secure; powered axles not leaking
  • Lift axle mechanism (if equipped)
  • Brakes: adjustment, drums or rotors, hoses, chambers and slack adjusters
  • Side-marker lights and reflectors: clean, working, proper color (red at the rear, amber elsewhere)

Rear

  • Rear clearance, identification and tail lights: clean, working, red
  • Reflectors clean and red
  • Right rear turn signal working and the proper color
  • License plate present, clean and secure
  • Splash guards present, not damaged, properly fastened, not dragging or rubbing the tires
  • Cargo secure; tailgate, end gates and rear doors closed and latched

Left side

  • Check everything you checked on the right side
  • Battery box (if not under the hood): securely mounted, cover in place, no damage or leaks

Step 6: Check the signal lights

Get in, turn off all lights, then turn on the stop lights (apply the trailer hand brake or have a helper press the brake pedal) and the left turn signal.

  • Left front turn signal: clean, working, proper color (amber or white on signals facing forward)
  • Left rear turn signal and both stop lights: clean, working, proper color (red, yellow or amber)

Step 7: Start the engine and check the brakes

Air brake checks apply only to vehicles with air brakes. See our air brakes test for the pressures to know.

  • Air brakes: leakage rate, low-pressure warning, spring brakes come on automatically, rate of air pressure build-up, governor cut-out and cut-in pressures
  • Parking brake: fasten your seat belt, let the vehicle move forward slowly and apply the parking brake; it should stop the vehicle
  • Service brake: at about 5 mph, push the brake pedal firmly; pulling to one side, an unusual pedal feel or delayed stopping can mean brake trouble
  • Hydraulic brakes (if equipped): pump the pedal three times, then press firmly and hold for five seconds; the pedal should not move

Air brake numbers

For the leakage, warning and build-up pressures you need for step 7, see the table on our air brakes practice test.

Frequently asked questions

What should I say during the pre-trip inspection test?

Name each part and explain what you are checking, for example: "The brake hose is secure, with no cracks, cuts or leaks." Examiners grade what you say, so do not just look.

How much tread do tires need?

Front (steering) tires need at least 4/32 inch of tread in every major groove. Other tires need at least 2/32 inch.